Digi M10 Technical overview and Przewodnik Instalacji Pobierz pdf (Strona 20)

Chapter 3: Assembling Legs 15

Attaching the Front Beam

To attach the front Beam:

1 Align the pins on the underside of the Beam with the holes in the top of the Legs. Be sure to orient the front Beam so that the

pins on the top are closer to the center of the frame.

2 Using four fasteners and washers (included) per mount, attach the Beam across the front of the Legs using two Beam Mounting

Plates as shown in Figure 4. Do not tighten the fasteners.

Fasteners, Washers, and Tools for Legs to Beams

Fastener

M8x40

Washer

Tool

M6 Hex

Figure 4. Orientation of the pins on the top of the front beam

(Not to scale)

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 81 82

S6 Installation Guide 1
Legal Notices 2
Contents 3
S6 Installation Guideiv 4
Part I: Introduction 5
Chapter 1: Introduction 6
Overview of Installation 7
What’s Included 7
Activation and Registration 8
About This Guide 9
About www.avid.com 9
Master Section Modules 10
Channel Modules 11
Knob Module 12
Display Module 12
Module Layout 13
S6 Installation Guide10 15
Part II: Frames 16
Chapter 3: Assembling Legs 18
Attaching the Back Beam 19
Attaching the Front Beam 20
(Not to scale) 21
Attaching the End Shelves 22
Leveling the Leg Frame 22
How to Proceed 23
Before You Begin 24
Frame Chassis Kit Components 25
Assembling the Chassis 26
S6 Installation Guide22 27
M3x6 SEMS (7760-30025-01) 28
#1 Phillips 28
Important 29
Attaching the Back Feet 30
Leveling the Chassis 32
Attaching the Bolster 33
M5x12 FHCS 34
M5x8 SHCS (7760-30593-00) 35
Installing Side Covers 36
Part III: Modules 38
Overview 40
Installing the Power Strip 41
Ethernet Switch” on page 40 43
6-Chassis Systems 44
7-Chassis Systems 44
9-Chassis Systems 44
S6 Installation Guide40 45
Installing PSUs 46
To connect power to PSUs: 47
12 3 4 512 3 4 5 49
12 3 4 5 49
12 3 4 512 3 4 5 12 3 4 5 50
12 3 4 5 12 3 4 512 3 4 5 51
7- and 9-Chassis Systems 52
S6 Installation Guide48 53
To attach the Side Covers: 55
M4x14 FHPH 56
#2 Phillips 56
Chapter 6: Installing Modules 58
Installing Modules 59
S6 Installation Guide56 61
Automation 62
Installing the Master Module 63
Setting the Touchscreen Angle 64
Installing Fill Panels 65
Installing Display Modules 65
Gigabit 66
Ethernet RJ45 66
S6 Installation Guide62 67
Chapter 7: How to Proceed 68
Installing Compression Panels 69
Installing T Strips 70
Figure 40. Upper Rear Panel 71
Updating S6 System Software 72
Configuring the S6 System 73
Part IV: Appendices 74
Removing Modules 76
Disassembling a Frame 77
Appendix B: Compliance 78
Australian Compliance 79
Canadian Compliance 79
CE Compliance 79
Safety Compliance 80
Korea Class B EMC Compliance 80
S6 Installation Guide76 81
Technical Support (USA) 82
Product Information 82

Komentarze do niniejszej Instrukcji

Brak uwag

Digi M10 Technical overview and Przewodnik Instalacji Strona 20

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Digi M10 Technical overview and